lock nut

美 　英

• un.〔機〕放松螺母；對開螺母；鎖緊螺母；鎖緊螺帽
• 網絡防松螺帽；防松螺母；鎖定螺母

英漢解釋

un.	1. 〔機〕放松螺母;對開螺母 2. 鎖緊螺母 3. 鎖緊螺帽 4. 鎖錠螺母 5. 防構螺帽 6. 保險螺母 7. 防松螺母

例句

Disassemble the door-frame, loosen the lock nut, and hammer it out.

分解門鎖，松開鎖住部分，然后將折斷部分敲出。

Small bearings with a bore diameter up to 100 mm can be properly mounted by measuring the lock nut tightening angle .

孔徑最大為100毫米的小型軸承可通過測量鎖定螺母的緊固角度正確安裝。

Can counterclockwise unscrewing the grip the lock nut and adjust control again, until the nut spin twist clearance fit.

可以逆時針擰松握把根部的鎖緊螺母，再左右旋擰調整螺母，直到間隙合適為止。

The problems in lock nut of roll axis and sleeve of precision rolling mill are analyzed, some measures proposed, good result got.

針對高速線材生產中，精軋機輥軸及隔套鎖緊螺母存在的問題進行分析，提出了改進措施，取得了較好效果。

Disc is fastened securely to disc hanger with a lock nut and cotter pin .

通過一個鎖緊螺母和開口銷將閥瓣安全緊固在閥瓣支架上。

After completing adjustments, tighten the lock nut and replace the fast fill lever cap.

在調節(jié)完成后，緊固鎖緊螺母，重新安裝快速進水手柄帽。

The two-piece Hard Lock Nut is easy to install, requiring only the use of a wrench.

雙件套強力鎖緊螺母安裝簡便，只需要一個扳手就行。

lock nut holds the setting at the precise measurement.

防松螺母使設置保持精密的測量。

I know what I'm doing. I don't need any lock nut.

我知道我在做什么我不需要什么螺母

V. Notes 1. Replacement blades to compress the lock nut, otherwise, saw people flying out of injury accidents caused by equipment;

五、注意事項1.更換鋸片必須鎖壓緊螺母，否則，鋸片飛出造成設備人傷事故；

LOCATING CONE LOCATION KEY LOCATION PIN LOCK BEAD LOCK NUT CHAIN STEEL LOCKER LOWER MCS(MASTER MAGNET CONTRL SURFACE)

裝料（裝載）重量支撐、限止器定位錐定位鍵定位銷拉延檻鎖緊螺母鏈條下刀塊

The strap tension force is adjusted ex works with the aid of hex cap lock nut

扎帶的張力是通過六角頭鎖緊螺母來實現的

Measuring the lock nut tightening angle

測量鎖定螺母的擰緊角

Loose optical wedge lock nut (No. 7 in Fig. 1) at both sides of sighting telescope center by special wrench;

用專用扳子將瞄準鏡中部左右兩個光楔鎖緊螺母（圖1序號7）松開；

Clamping sleeve with lock nut

帶鎖母的夾緊套

Difference in shaft lock nut

軸差內鎖緊螺母

Motor half coupling lock nut

電動機半聯軸器的鎖緊螺母

check (or jam, or lock) nut

鎖[緊螺]帽，并緊螺帽